Parts & Accessories

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Convert Roval wheels with 142 or 142+ to be used with Boost spacing (110 /148mm) suspension forks and frames. - Kits include front and rear hub end caps, rotor spacers, and kit specific rotor bolts - Compatible with select MY13-16 Roval Wheels. Choose the appropriate SKU for each wheelset - Each conversion kit requires the existing rear wheel to be re-dished to center. Consult an authorized dealer to perform this operation

- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Right Axle End Cap

- Original equipment freehub bodies to fit SRAM hubs and wheels. - Includes Drive Side Axle End Cap

Keep your skewers properly situated with these quality skewer springs from Salsa.

Can be used with Stan's ZTR rims to make them airtight or used as a lightweight rim tape in any rim. A single 10-yard roll will tape five 26-inch rims or four 29-inch rims or two wide road clincher rims. 21mm width fits: - ZTR Olympic - ZTR Iron Cross - ZTR 355 - ZTR Alpine - ZTR Crest - ZTR Alpha 340 (2 layers) - ZTR Alpha 400 (2 layers) - Most road clincher rims 25mm width fits: - ZTR 355 (26", 650b, 29") - ZTR Crest - Crest MK3 - ZTR Arch EX - ZTR Flow EX - Crest S1 27mm width fits: - ZTR Flow EX - ZTR Bravo - ZTR Hugo 52mm - Arch S1 - ZTR Rapid 28 - ZTR Rapid 30 - Arch MK3 30mm width fits: - ZTR Flow MK3

The same spoke thread treatment used by Stan's pro wheel builders is now available to everyone. Stan's SRD Spoke Powder fills the threads of the spoke and functions as both a lubricant during assembly and a thread lock once built. Each bottle contains 24g (.8oz) which will treat approximately 300 wheels. The PTFE powder in Stan's SRD Spoke Powder acts as a barrier, keeping the metal of the nipple from bonding to the metal of the spoke and preventing spoke wind up during build or adjustment. In promoting a smoother turning nipple, the powder also ensures more accurate and consistent wheel builds, with less “ping and pop" during and after the build. The powder also fills the threads of the spoke to act as a thread lock that prevents loosening and de-tensioning and is particularly well suited for mechanically locking nipples such as Sapim's Secure Lock. - Improves tension consistency and overall build quality - Prevents spoke wind up - Offers secure thread lock between spoke and nipple - Prevents corrosion between spoke and nipple - Can be used dry or as a slurry - Works great with mechanically locking nipples

Surly Rim Strips have one job and they do it well. They cover the cutouts in your rim and — if you're running a tube — they protect it from spoke heads and other sharp matter (okay, so maybe they have TWO jobs but they do them both really well.) Rim strips are crucial and should be used with all Surly rims. Ours come in an array of colors so you can really "express yourself." Surly Rim strips are available in two different materials: PVC and Nylon. PVC is great if you plan on only running tubes. However, if there's any part of you that wants to try this tubeless thing you've been hearing about, Nylon strips are just the ticket. They're thinner and offer minimal stretch so they stay put and lay nicely inside the rim to provide a secure seal. Plus, they're lighter which we all know means you'll go faster… maybe.

High-quality replacement skewer to keep the bike moving. - OE Replacement skewers - Available in a variety of OE replacement lengths - Measure hub width and skewer length to ensure proper compatibility

High-quality replacement skewer to keep the bike moving. - Thru Axle for Trek ABP and Convert systems - Available in a variety of OE replacement lengths

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

Wheels Manufacturing Outer Axle Nuts are high-grade steel nuts that provide secure wheel fixing for solid-axle wheels. - 14mm x 1mm (1411-AN) sold in pairs - All others sold individually

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Sovos 9mm x 1, front hub - Compatible with 9mm x 1 axle - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag COMPATIBLE HUBS: - Sovos 9mm x 1, front hub - Taiwanese and similar front hubs with 9mm x 1 axle

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Fits: Joytech 9mm x 26, front hub - Compatible with 9mm x 26 axle - Cone Wrench Size: 13mm - Threads: 9mm x 26 - Diameter: 15.0mm - Length: 12.8mm - 1 cone per bag - Note: O-ring / seal not included. COMPATIBLE HUBS: - Joytech 9mm x 26, front hub - Taiwanese hubs with 9mm x 26 axle - 105 SC 1055 8-speed Rear - 105 SC 1056 7-speed Rear - XT-II M732 7-speed Rear

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian front hubs - Type: Hollow Axle - Threads: 9mm x 26tpi - Diameter: 9mm - Length: 110mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 126mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 137mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 130mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 141mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian rear hubs with 130mm spacing - Type: Hollow Axle - Threads: 10mm x 26tpi - Diameter: 10mm - Length: 141mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits Campagnolo / Italian rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 26tpi - Diameter: 10mm - Length: 146mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs with 126mm spacing - Type: Hollow Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 137mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese front hubs - Type: Hollow Axle - Threads: 9mm x 1 - Diameter: 9mm - Length: 110mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Taiwanese hubs - Type: Solid Axle - Threads: 9.5mm x 26tpi - Diameter: 9.5mm - Length: 155mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many tandem hubs - Type: Solid Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 187mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many BMX hubs - Type: Solid Axle - Threads: 9.5mm x 24tpi - Diameter: 9.5mm - Length: 180mm - 1 axle per bag

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag

- Anodized aluminum - 50 nipples per bag - 12mm length

These die-cut borderless decals provide a distinctive look to go with the distinctive sound and aero-advantage of Zipp wheels rolling at 45km an hour. Zipp’s Matte white and Matte black decals also are still available. Each decal kit has seven decals sufficient to cover one wheel and two matching valve-hole decals. Note: Before applying the decals, make sure the rim surface is free of dirt and debris. We recommend a gentle wipe with acetone or rubbing alcohol. Peel the white backing sheet from the decal, orientate, position and gently press the decal onto the rim surface. Starting at one end, remove the surface clear cover slip and then work the decal into the dimples using a 3M squeegee.

Help ensure your rotors are not damaged, contaminated in transit, or in storage with this simple solution. This also helps protect anything that may come into contact with the rotor during transport. - Protects rotors during transit - Neoprene cover to protect against water and grease - Reinforced gusset and drawstring to protect the edges of the rotor and to cinch down tightly during transit

Wheel Freehub Kit SS 176/177 SRAM XDR - End Caps Not Included Compatible With: WH-202-CCR-A1, WH-202-TLD-A1, WH-202-TUD-A1, WH-302-CCD-A1, WH-302-CCR-A1, WH-302-TLR-A1, WH-303-CCR-B1, WH-303-TLD-A1, WH-303-TUD-B1, WH-303-TUR-B1, WH-30C-CLD-A1, WH-30C-CLR-A1, WH-404-CCR-A1, WH-404-CCR-B1, WH-404-TLD-A1, WH-808-CCR-B1, WH-808-TLD-A1, WH-SP9-CC30-A1, WH-SP9-CCD-A1, WH-SP9-CCR-A1, WH-SP9-TUD-A1

Wheel Freehub Kit—XDR Driver Body Kit—Zipp ZR1 Compatible With: WH-202-FTLD-A1, WH-303-F650-A1, WH-303-FTLD-A1, WH-303-FTLR-A1, WH-303-FTUD-A1, WH-303-FTUR-A1, WH-404-FTLD-A1, WH-404-FTLD-B1, WH-404-FTLR-A1, WH-808-FTLD-A1, WH-808-FTLR-A1, WH-SP9-TLD-A1, WH-SP9-TUD-A2, WH-SP9-TUR-A2